Note that the number at the end indicates the size to write in hex. Then we proceed to flashing OpenWrt itself (which we called nsa325.bin for less typing):
Zyxel firmware nsa320 usb mac#
Setenv bootcmd 'run setenv bootargs ubi part ubi ubi read 0x800000 kernel bootm 0x800000'Īfter the device reboots into the OpenWrt u-boot we adjust the device's MAC address (adjust the values, see the sticker under the NAS case): Now we set the correct environment variables:
Zyxel firmware nsa320 usb install#
If your USB stick isn't recognized/found by u-boot, try putting an active (powered) USB hub between the NAS and the flash drive.Īfter plugging in the USB stick (use the rear USB ports), into the NAS, with the correct files and booting into u-boot, first step is to install OpenWrt's u-boot: Make sure to write down your device's MAC address as we need to set it later! Otherwise it would get lost! You should first have downloaded the latest firmware files from the ZyXEL. At this point, I gave up on booting off USB and loaded Bohdi's 3.17 rootfs on the hard drive (OMV didn't add much to what I needed). Looks like a timeout issue with the stock uBoot USB subsystem.
Please note that to write to NAND you have to erase the NAND first, which means all data on the NAND will be deleted! Meaning stock firmware, bootloader, settings and everything will be gone! So make sure you got the proper files ready before you start as it's vital that you flash the new bootloader before you restart your device as it would otherwise get soft-bricked. Media Server NSA210, NSA221, NSA310, NSA320, NSA325 Default Login Details Web. Where I left off there was that after installing the script, my NSA320 simply would not boot off of the USB using the stock uBoot. Use the latest u-boot.kwb from the 18.x.x release instead. Rename the -factory.bin to something simple like nsa325.bin.Īttention: the u-boot.kwb from 19.x.x release is bugged and won't allow access to any mass storage. We will then copy the required files to the USB stick and command the device through a terminal (using serial) to load and flash our files to NAND.Ĭopy the u-boot.kwb and -factory.bin files to a FAT32 formatted USB stick with msdos partition table (single partition).
Zyxel firmware nsa320 usb serial#
Not only can it share the contents of a USB disk across a network, but it did the same for a Fuji digital camera and a SD card plugged into a USB memory card reader.We require a USB stick (FAT32 formatted, single partition) and a 3.3V USB to serial adapter. It also worked flawlessly when sharing a USB printer. It can even be used as a server for Logitech Squeezebox network audio players, which don't work with UPnP. We had no problems using the NSA320 has a UPnP media server, although oddly it only worked as an iTunes music server once we had set a password. Creating user accounts was very straightforward, though – setting quotas and giving each user different access permissions to different folders all happens from within the same uncluttered window.
The main administration interface runs in a web browser, but while it is logically organised, the nested menus can look intimidating. When two disks are fitted, it also provides options to configure the RAID array. The discovery utility got us up and running very quickly, letting us quickly create up to five user accounts with or without administrator privileges. Removing a disk requires a plastic tool that's stored on the inside of the front panel, and it does require some force. These carriers could be more clearly marked, though, as it’s not entirely clear which way to screw them on. Once plastic carriers are screwed onto the sides of each SATA hard disk, they can be slotted into the bays located behind the removable front panel. Installing and removing disks is slightly fiddly, but it's likely you'll never need to remove them.
0 kommentar(er)
